+49 (0)30 66778166
de German

Refill Toner (Instructions) Brother TN-241, TN-245, HL-3140 and HL-3170

Refill instructions:

TN-241, TN-245, HL-3140 and HL-3170

 

This toner fits the following Brother devices:

 

Brother DCP:           DCP-9015 CDW, DCP-9020 CDW

Brother HL:              HL-3140CW, HL-3150CDN, HL-3150 CDW, HL-3170 CDW

Brother MFC:           MFC-9130 CW, MFC-9140 CDN, MFC-9330 CDW, MFC-9335 CDW and MFC-9340 CDW

 

Preparation for filling:
Before you melt the filler opening into the cartridge, you have to remove the label as shown in 1 picture. Then take the hot soldering iron and melt the filler opening the marked spot as shown in Figure 2. After melting the opening, take care to cleanly deburr the opening. Please make sure that no plastic shavings get into the cartridge. These plastic shavings will damage the printing mechanism of the toner cartridge and could degrade the printed image.


Before you fill the toner cartridge, you have to remove the old toner that is still present. Make sure you do it in the fresh air. Due to different properties between new and existing toners, the mixed toner can clump together. Shake the remaining toner into a tight plastic bag.

 

Brother TN-241, TN-245, HL-3140 and HL-3170 Remove label

 

 

Brother TN-241, TN-245, HL-3140 and HL-3170, Drill a hole

 

Brother TN-241, TN-245, HL-3140 and HL-3170, Refill toner

 

Brother TN-241, TN-245, HL-3140 and HL-3170, Close the filler opening

Install the reset lever on Brother TN-241, TN-245, HL-3140, and HL-3170:
To install the reset lever, you must remove the side cover. Loosen the screws that can be seen in the picture. The cover is now only attached with a barb. Make sure to loosen the barb with a screwdriver before removing the cover. Take the removed side cover and carefully insert the spring of the reset lever.

 

You can then insert the reset lever. Make sure that the section without teeth points to the right as shown in the picture. Now all you have to do is tension the spring. Use a flat-blade screwdriver to push the spring behind the plastic tab. The reset lever shows "full" and you can continue printing. If the reset lever is already there, all you have to do is turn it back.

Brother TN-241, TN-245, HL-3140 and HL-3170, loosen two screws

 

Brother TN-241, TN-245, HL-3140 and HL-3170, Loosen barbs

 

 

Brother TN-241, TN-245, HL-3140 and HL-3170, Insert spring

 

Brother TN-241, TN-245, HL-3140 and HL-3170, Tension spring

 

 

You are now done with filling your toner cartridge. Use a test print to test whether you have succeeded:

 

https://eurotone.de/pages/testseiten-fur-drucker-und-toner-tinte

 

 

Safety note for handling refill toner:
Toner powder can be harmful if improperly handled. We expressly recommend the use of breathing apparatus when filling the toner cartridge. In addition, carbon powders are extremely flammable in a suitable mixture of oxygen. Also, be careful not to touch the photosensitive drum or expose it to direct sunlight. This can lead to incorrect printouts. Eurotone assumes no responsibility for the success or failure of the procedure described

All manufacturers and brand names are used only to indicate compatibility and are the property of their respective owners. Eurotone assumes no guarantee, responsibility or liability for the success or failure of the procedure described as a result of the procedures in its instructions.